The hardware schedule, and how to read one.
A hardware schedule is the document that decides what every opening in the building gets. Here is how it's organized, who produces it, who should be checking it, and where it goes wrong.
The hardware schedule is where every door in a building gets decided. It's produced early, read by few people, and responsible for a large share of the problems that turn up years later — because a mistake in a schedule gets installed hundreds of times before anybody notices.
What it is
A hardware schedule is a written document listing every opening in a project and specifying exactly what hardware goes on it: hinges, lock or exit device, closer, stops, seals, thresholds, and any electrified components — with manufacturer, product number, finish and function for each.
It's part of the construction documents, usually Division 08 71 00 under the CSI MasterFormat system. It isn't a shopping list. It's a specification, and it carries code consequences: fire ratings, egress function and accessibility all get determined here.
How it's organized: hardware sets
The schedule doesn't list every door individually with a full hardware list. That would be enormous and unreadable. Instead it groups openings into hardware sets — sometimes called heading numbers or HW sets.
A hardware set is a named bundle of hardware for a particular kind of opening. The body of the schedule then assigns each door number to a set.
A set typically reads something like this:
HW SET 04
3 EA Hinge BB1191 4.5 x 4.5 NRP US26D Hager
1 EA Exit Device 98-L-F x 996L-06 US26D Von Duprin
1 EA Closer 4040XP-SCUSH 689 LCN
1 EA Kick Plate 10" x 2" LDW B-CS US32D Trimco
1 SET Seals S88 BL Pemko
1 EA Threshold 171A Pemko
Read it as: quantity, hardware type, product number, finish, manufacturer. The product number carries
the function — in the example above, 98-L-F is a Von Duprin 98 series rim exit device, lever trim,
fire-rated. NRP on the hinge means non-removable pin, used on outswinging exterior doors so the pin
can't be driven out from the unsecured side.
Finishes are called out by code: US26D (BHMA 626) is satin chrome, US32D (BHMA 630) is satin
stainless, and 689 is aluminum paint. The US codes are the older system, and both still turn up.
These get mixed within a set routinely and correctly — a closer in 689 next to levers in US26D is
normal, not an error.
Who produces it, who reviews it
Produced by one of three parties, depending on project size: the architect's specification writer, an independent hardware consultant, or the hardware distributor bidding the job. On a large project the schedule frequently comes from the distributor as part of the submittal. That's efficient, and a good distributor's schedule can be excellent, but it's still worth a second set of eyes before it's approved.
Reviewed by the architect and, ideally, somebody who didn't write it. This is the step that gets skipped, and it's the step that catches problems while they are still free to fix.
Substitution requests
When a contractor proposes a different product than the one specified, that's a substitution request. Some are entirely legitimate — lead times, discontinued products, genuine equivalents at lower cost. Some are a grade drop or a function change dressed up as an equal.
The review question is always the same three things: is it the same function, the same grade, and does it carry the same listings — fire rating, ADA compliance, and any required certifications. A product can match on price and appearance and fail on all three.
Common errors
These are the ones worth checking for specifically, because they are both frequent and consequential:
- Function doesn't match the door's use. A classroom function where a storeroom function was needed, or an office function on a door that has to lock from the corridor. Nobody notices until somebody gets locked in or out.
- Fail-safe versus fail-secure specified wrong on electrified openings. This is a code decision driven by egress and occupancy, not a preference, and getting it backwards is a life-safety issue.
- Grade drops buried in a long schedule. Easy to miss on a hundred-opening project.
- Hardware that voids a fire label. Unlisted components on a rated assembly.
- Handing errors. Doors listed with the wrong hand or bevel, which means hardware arrives that physically can't be installed and the project stalls at the worst moment.
- Closers sized without regard to arm type. A parallel arm at the same nominal size delivers less closing power than a regular arm, so the door doesn't latch.
- Missing coordination on pairs. No coordinator, no astragal, or flush bolts left off entirely.
- Threshold and seal conflicts with ADA level-change limits.
When to get it reviewed
The cheapest moment is before the submittal is approved. The second cheapest is before anything ships. After installation, correcting a schedule error means paying for the hardware twice and paying labor to remove the first set — and on a rated opening it can mean patching or replacing doors.
A review against the drawings, the door schedule and the applicable codes takes a fraction of what a single opening costs to redo.
Related
Need this applied to a real opening?
Reference material only goes so far. Tell me what the door is doing and what building it's in. A free 15-minute phone consult is often enough to tell what you're dealing with.